휴즈뱅크

제품소개

CUSTOMER CENTER
고객의 소리에 귀기울이겠습니다
T : 02-2615-4890
F : 02-2615-4892
E : fusebank@hanmail.net
M1206 SERIES
HOME > 회사소개 > M1206 SERIES


 


 

Product NameN1206 A SERIES
VoltageAC 125 / 250V
CharacteristicTime Delay Type
FeaturesEnvironmentally conscious
- Pb Free, Halogen Free, Antimony Free
- REACH (SVHC), RoHS
High performance material can protect PCB against ambient temperature.
SolderabilityPre Heating : 150℃ ± 10℃, 120sec
Solder bath : 245℃ ± 5℃, 10s ± 1sec
Reflow : 260℃ ± 10℃, 10s ± 1sec
Delatinglower temperature : -40℃
higher temperature : +125℃


Agency Approvals
AGENCYAGENCY FILE No.AMPERE RANGE
E3284080.50A~5.00A
E3284080.50A~5.00A
CA12P31300.50A~4.00A(125V)
CA15P30470.50~4.00A (125V)
Dimensions
Electrical Characteristics for Series
% of Ampere RatingAmpere RatingOpening Time
at 25℃
100%0.50A~5.00A4hour minimum
200%0.50A~5.00A1~120 sec
Device TypeDimensions(mm) ± 0.1mm
L1L2WT1T2CDEFG
N1206 A Series3.22.41.61.0(0.5)2.10.551.02.40.4
Recommended Pad LayoutsDimensions(mm)
abcde
1.41.71.42.264.5


Electrical Specification
Ampere
Rating
(A)		MarkingRated
Voltage
(V)		Fusing Time(sec)Internal
Nominal
R(mΩ)		Rated
Ambient
Temperature		Operating Temperature Range
0.50AAC125/2501~120 sec
at 250% rated
current		206Body : 95℃
Contact : 70℃		-40℃
to
+125℃
0.75AAD125/250128
1.00AAE125/25080
1.25AAF125/25073
1.50AAG125/25069
1.60AAG1125/25058
1.75AAH125/25046
2.00AAI125/25029
2.50AAJ125/25027
3.00AAK125/25022
3.50AAL125/25019
4.00AAM125/25011
4.50AAN125/2509
5.00AAO125/2507

※ Best Choice of Micro Fuse : Full Load Ampere (F.L.A) for Electronic System Operation × 125%
   (ex) Micro Fuse Choice for 1A Electronic System : 1A × 125% = 1.25A
   (This electronic system must using of Micro Fuse with 1.25A rated current.) 
Performance CharacteristicsTest Enviroment -
Ambient Temperature : 10℃ - 50℃ ,
Humidity : 45% - 85%
NoTest ItemTest ConditionRequirement
1Resistivity
Test
  • Temp : Ambient
  • It is applied for 1 hour and 15min off at 110% of rated current
  • Duration : 100 Hours(Endurance Test)
  • Measure Voltage drop. Do not exceed 10%
2Time/Current
Characteristic
  • Apply 250% of rated current
  • Fusing Time : 1~120 sec
3Temperature
Rising
  • Measure the temperature at surface of device
  • Body : 95℃ Max
  • Contact : 70℃ Max
4Cycling
Test
  • Lower temperature : -40℃
  • Upper temperature : +125℃
  • No. of cycling Time : 5
  • No Open during cycling
5Endurance
Test
  • Test condition : Nominal ambient Temp. and Relative humidity
  • Test potential
    1. Cycle of 1hour “ON” and 15min “OFF” at 105% rated current for 100 times.
    2. After above the test, inflict 125% rated current for 1hour
  • The voltage drop across the fuse after the test shall not have increased by more than 10% of the value measured before test

Derating Curve
Reflow Condiction
Time / Current Characteristics

검색