휴즈뱅크

제품소개

CUSTOMER CENTER
고객의 소리에 귀기울이겠습니다
T : 02-2615-4890
F : 02-2615-4892
E : fusebank@hanmail.net
N6125 SERIES
HOME > 회사소개 > N6125 SERIES


 


 


Product NameN6125 C SERIES
VoltageAC 125 / 250V
CharacteristicFast Acting Type
FeaturesEnvironmentally conscious
- Pb Free, Halogen Free, Antimony Free
- REACH (SVHC), RoHS
High performance material can protect PCB against ambient temperature.
SolderabilityPre Heating : 150℃ ± 10℃, 120sec
Solder bath : 245℃ ± 5℃, 10s ± 1sec
Reflow : 260℃ ± 10℃, 10s ± 1sec
Delatinglower temperature : -40℃
higher temperature : +125℃


Agency Approvals
AGENCYAGENCY FILE No.AMPERE RANGE
E3284080.50A~5.00A
E3284080.50A~5.00A
SG05002-14004~11003A0.50A~5.00A
(125V)
SG05002-14003~11001A0.50A~5.00A
(250V)
Dimensions
Electrical Characteristics for Series
% of Ampere RatingAmpere RatingOpening Time
at 25℃
100%1.00A~5.00A4hour minimum
200%1.00A~5.00A5sec maximum
Device TypeDimensions(mm) ± 0.1mm
L1L2WT1T2CDEFG
N6125 C Series6.14.52.71.2(0.5)3.21.451.54.50.8
Recommended Pad LayoutsDimensions(mm)
abcde
2.3752.82.3753.47.55
Electrical Specification
Ampere
Rating
(A)		MarkingRated
Voltage
(V)		Fusing Time (sec)Internal
Nominal
R(mΩ)		Rated
Ambient
Temperature		Operating Temperature Range
0.50ACC125/2505 sec maximum
at 250% rated
current		350Body : 95℃
Contact : 70℃		-40℃
to
+125℃
0.75ACD125/250139
1.00ACE125/25078
1.25ACF125/25062
1.50ACG125/25048
1.60ACG1125/25045
1.75ACH125/25039
2.00ACI125/25028
2.50ACJ125/25023
3.00ACK125/25019
3.50ACL125/25016
4.00ACM125/25014
4.50ACN125/25012
5.00ACO125/25010

※ Best Choice of Micro Fuse : Full Load Ampere (F.L.A) for Electronic System Operation × 125%
   (ex) Micro Fuse Choice for 1A Electronic System : 1A × 125% = 1.25A
   (This electronic system must using of Micro Fuse with 1.25A rated current.) 


Performance CharacteristicsTest Enviroment -
Ambient Temperature : 10℃ - 50℃ ,
Humidity : 45% - 85%
NoTest ItemTest ConditionRequirement
1Resistivity
Test
  • Temp : Ambient
  • It is applied for 1 hour and 15min off at 110% of rated current
  • Duration : 100 Hours(Endurance Test)
  • Measure Voltage drop. Do not exceed 10%
2Time/Current
Characteristic
  • Apply 200% of rated current
  • Fusing Time : 5 sec maximum
3Temperature
Rising
  • Measure the temperature at surface of device
  • Body : 95℃ Max
  • Contact : 70℃ Max
4Cycling
Test
  • Lower temperature : -40℃
  • Upper temperature : +125℃
  • No. of cycling Time : 5
  • No Open during cycling
5Endurance
Test
  • Test condition : Nominal ambient Temp. and Relative humidity
  • Test potential
    1. Cycle of 1hour “ON” and 15min “OFF” at 105% rated current for 100 times.
    2. After above the test, inflict 125% rated current for 1hour
  • The voltage drop across the fuse after the test shall not have increased by more than 10% of the value measured before test


Derating Curve
Reflow Condiction
Time / Current Characteristics

검색