휴즈뱅크

제품소개

CUSTOMER CENTER
고객의 소리에 귀기울이겠습니다
T : 02-2615-4890
F : 02-2615-4892
E : fusebank@hanmail.net
N6125 SERIES
HOME > 회사소개 > N6125 SERIES


 


 


Product NameN6125 A SERIES
VoltageAC 125 / 250V
CharacteristicTime Delay Type
FeaturesEnvironmentally conscious
- Pb Free, Halogen Free, Antimony Free
- REACH (SVHC), RoHS
High performance material can protect PCB against ambient temperature.
SolderabilityPre Heating : 150℃ ± 10℃, 120sec
Solder bath : 245℃ ± 5℃, 10s ± 1sec
Reflow : 260℃ ± 10℃, 10s ± 1sec
Delatinglower temperature : -40℃
higher temperature : +125℃


Agency Approvals
AGENCYAGENCY FILE No.AMPERE RANGE
E3284080.50A~5.00A
E3284080.50A~5.00A
CA12P31601.00A~3.15A(250V)
SG05002-12001,2
SG05002-10001A,3A		1.00A~3.15A(250V)
1.00A~5.00A(125V)
KR-KE-000541.00A~3.15A(250V)
JET 6603-31007-2001-10.50A~5.00A(250V)
40038156, 400374650.50A~2.00A(250V)
CQC 130121005721.00A~1.60A(250V)
CA15P60481.00~3.15A (250V)
CA15P30491.25~2.50A (250V)
Dimensions


Electrical Characteristics for Series
% of Ampere RatingAmpere RatingOpening Time
at 25℃
100%1.00A~5.00A4hour minimum
250%1.00A~5.00A1~120 sec
Device TypeDimensions(mm) ± 0.1mm
L1L2WT1T2CDEFG
N6125 A Series6.14.52.71.2(0.8)3.21.451.54.50.8
Recommended Pad LayoutsDimensions(mm)
abcde
2.3752.82.3753.47.55


Electrical Specification
Ampere
Rating
(A)		MarkingRated
Voltage
(V)		Fusing Time(sec)Internal
Nominal
R(mΩ)		Rated
Ambient
Temperature		Operating Temperature Range
0.35AAB2501~120 sec
at 250% rated
current		1020Body : 95℃
Contact : 70℃		-40℃
to
+125℃
0.50AAC125/250255
0.75AAD125/250141
1.00AAE125/250133
1.25AAF125/25091
1.50AAG125/25075
1.60AAG1125/25072
1.75AAH125/25045
2.00AAI125/25022
2.50AAJ125/25020
3.00AAK125/25023
3.50AAL125/25021
4.00AAM125/25019
4.50AAN125/25017
5.00AAO125/25016

※ Best Choice of Micro Fuse : Full Load Ampere (F.L.A) for Electronic System Operation × 125%
   (ex) Micro Fuse Choice for 1A Electronic System : 1A × 125% = 1.25A
   (This electronic system must using of Micro Fuse with 1.25A rated current.) 


Performance CharacteristicsTest Enviroment -
Ambient Temperature : 10℃ - 50℃ ,
Humidity : 45% - 85%
NoTest ItemTest ConditionRequirement
1Resistivity
Test
  • Temp : Ambient
  • It is applied for 1 hour and 15min off at 110% of rated current
  • Duration : 100 Hours(Endurance Test)
  • Measure Voltage drop. Do not exceed 10%
2Time/Current
Characteristic
  • Apply 250% of rated current
  • Fusing Time : 1~120sec
3Temperature
Rising
  • Measure the temperature at surface of device
  • Body : 95℃ Max
  • Contact : 70℃ Max
4Cycling
Test
  • Lower temperature : -40℃
  • Upper temperature : +125℃
  • No. of cycling Time : 5
  • No Open during cycling
5Endurance
Test
  • Test condition: Nominal ambient Temp. and Relative humidity
  • Test potential
    1. Cycle of 1hour “ON” and 15min “OFF” at 105% rated current for 100 times.
    2. After above the test, inflict 125% rated current for 1hour
  • The voltage drop across the fuse after the test shall not have increased by more than 10% of the value measured before test


Derating Curve
Reflow Condiction
Time / Current Characteristics

검색